EN 10106:2007
(Main)Cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state
Cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state
This European Standard specifies the grades of cold-rolled non-oriented electrical steel sheet and strip in nominal thicknesses of 0,35 mm, 0,50 mm, 0,65 mm and 1,00 mm. In particular, it specifies general requirements, the magnetic properties, geometric characteristics and tolerances, technological characteristics as well as the inspection procedure.
This European Standard applies to materials supplied in the fully annealed condition intended for the construction of magnetic circuits. It does not apply to semi-processed material.
These magnetic materials correspond to C.2.3.2.1 of IEC 60404-1:2000.
Kaltgewalztes nicht kornorientiertes Elektroblech und -band im schlussgeglühten Zustand
Bandes et tôles magnétiques en acier à grains non orientés laminées à froid et livrées à l'état fini
Hladno valjana neorientirana elektropločevina in trakovi
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed stateBandes et tôles magnétiques en acier a grains non orientés laminées a froid et livrées a l'état finiKaltgewalztes nicht kornorientiertes Elektroblech und -band im schlussgeglühten ZustandTa slovenski standard je istoveten z:EN 10106:2007SIST EN 10106:2007en77.140.50SROL]GHONLFlat steel products and semi-productsICS:SIST EN 10106:19971DGRPHãþDSLOVENSKI
STANDARDSIST EN 10106:200701-december-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10106September 2007ICS 77.140.50Supersedes EN 10106:1995
English VersionCold rolled non-oriented electrical steel sheet and strip deliveredin the fully processed stateBandes et tôles magnétiques en acier à grains non orientéslaminées à froid et livrées à l'état finiKaltgewalztes nicht kornorientiertes Elektroblech und -bandim schlussgeglühten ZustandThis European Standard was approved by CEN on 9 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10106:2007: E
EN 10106:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Classification and designation.5 4.1 Classification.5 4.2 Designation.5 5 Information supplied by the purchaser.5 5.1 Mandatory information.5 5.2 Options.6 5.3 Example of an order.6 6 General requirements.6 6.1 Production process.6 6.2 Form of supply.6 6.3 Delivery condition.7 6.4 Surface condition.7 6.5 Suitability for cutting.7 7 Technical requirements.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.