ASTM F1697-18

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1697 − 09 (Reapproved 2015) F1697 − 18
Standard Specification for
Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-
Wound Liner Pipe Rehabilitation of Existing Sewers and
1,2
Conduit
This standard is issued under the fixed designation F1697; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, stiffness factor, extrusion
quality, and a form of marking for extruded poly(vinyl chloride) (PVC) profile strips used for machine made field fabrication of
spirally wound pipe liners in the rehabilitation of a variety of gravity applications such as sanitary sewers, storm sewers, and
process piping in diameters of 6 to 180 in. and for similar sizes of non-circular pipelines such as arched or oval shapes and
rectangular shapes.
1.2 Profile strip produced to this specification is for use in field fabrication of spirally wound liner pipes in nonpressure sewer
and conduit rehabilitation, where the spirally wound liner pipe is expanded until it presses against the interior surface of the
existing sewer or conduit, or, alternatively, where the spirally wound liner pipe is inserted as a fixed diameter into the existing
sewer or conduit and the annular space between the liner pipe and the existing sewer or conduit is grouted.
1.3 This specification includes extruded profile strips made only from materials specified in 5.1.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
4
A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip (Withdrawn 2014)
4
A176 Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and Strip (Withdrawn 2015)
A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the
Hot-Dip Process
A879/A879M Specification for Steel Sheet, Zinc Coated by the Electrolytic Process for Applications Requiring Designation of
the Coating Mass on Each Surface
A924/A924M Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.67 on Trenchless
Plastic Pipeline Technology.
Current edition approved March 1, 2015April 1, 2018. Published April 2015July 2018. Originally approved in 1996. Last previous edition approved in 20092015 as
F1697F1697–09(2015).–09. DOI: 10.1520/F1697-09R15.10.1520/F1697-18.
2
The rehabilitation of existing pipelines and conduits by the insertion of a spiral wound liner pipe is covered by patents. (RibLoc Group Limited, Dry Creek, South
Australia, Australia and Danby of North America, Inc., Cary, NC, USA). Interested parties are invited to submit information regarding the identification of acceptable
alternatives to this patented item to the Committee on Standards, ASTM Headquarters, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Your comments will
receive careful consideration at a meeting of the responsible technical committee which you may attend.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document S
...

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1697 − 18
Standard Specification for
Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-
Wound Liner Pipe Rehabilitation of Existing Sewers and
1,2
Conduit
This standard is issued under the fixed designation F1697; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety, health, and
1.1 This specification covers requirements and test methods
environmental practices and determine the applicability of
for materials, dimensions, workmanship, stiffness factor, ex-
regulatory limitations prior to use.
trusion quality, and a form of marking for extruded poly(vinyl
1.6 This international standard was developed in accor-
chloride) (PVC) profile strips used for machine made field
dance with internationally recognized principles on standard-
fabrication of spirally wound pipe liners in the rehabilitation of
ization established in the Decision on Principles for the
a variety of gravity applications such as sanitary sewers, storm
Development of International Standards, Guides and Recom-
sewers, and process piping in diameters of 6 to 180 in. and for
mendations issued by the World Trade Organization Technical
similar sizes of non-circular pipelines such as arched or oval
Barriers to Trade (TBT) Committee.
shapes and rectangular shapes.
1.2 Profile strip produced to this specification is for use in
2. Referenced Documents
field fabrication of spirally wound liner pipes in nonpressure 3
2.1 ASTM Standards:
sewer and conduit rehabilitation, where the spirally wound
A167 Specification for Stainless and Heat-Resisting
liner pipe is expanded until it presses against the interior
Chromium-Nickel Steel Plate, Sheet, and Strip (With-
surface of the existing sewer or conduit, or, alternatively, where 4
drawn 2014)
the spirally wound liner pipe is inserted as a fixed diameter into
A176 Specification for Stainless and Heat-Resisting Chro-
the existing sewer or conduit and the annular space between the 4
mium Steel Plate, Sheet, and Strip (Withdrawn 2015)
liner pipe and the existing sewer or conduit is grouted.
A653/A653M Specification for Steel Sheet, Zinc-Coated
1.3 This specification includes extruded profile strips made
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)
only from materials specified in 5.1.
by the Hot-Dip Process
A879/A879M Specification for Steel Sheet, Zinc Coated by
1.4 The values stated in inch-pound units are to be regarded
the Electrolytic Process for Applications Requiring Des-
as standard. The values given in parentheses are mathematical
ignation of the Coating Mass on Each Surface
conversions to SI units that are provided for information only
A924/A924M Specification for General Requirements for
and are not considered standard.
Steel Sheet, Metallic-Coated by the Hot-Dip Process
1.5 The following precautionary caveat pertains only to the
D618 Practice for Conditioning Plastics for Testing
test method portion, Section 11, of this specification: This
D790 Test Methods for Flexural Properties of Unreinforced
standard does not purport to address all of the safety concerns,
and Reinforced Plastics and Electrical Insulating Materi-
als
1 D883 Terminology Relating to Plastics
This specification is under the jurisdiction of ASTM Committee F17 on Plastic
D1600 Terminology for Abbreviated Terms Relating to Plas-
Piping Systems and is the direct responsibility of Subcommittee F17.67 on
Trenchless Plastic Pipeline Technology.
tics
Current edition approved April 1, 2018. Published July 2018. Originally
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
approved in 1996. Last previous edition approved in 2015 as F1697–09(2015). DOI:
Compounds and Chlorinated Poly(Vinyl Chloride)
10.1520/F1697-18.
2
The rehabilitation of existing pipelines and conduits by the insertion of a spiral
wound liner pipe is covered by patents. (RibLoc Group Limited, Dry Creek, South
3
Australia, Australia and Danby of North America, Inc., Cary, NC, USA). Interested For referenced ASTM standards, visit the ASTM website, www.astm.org, or
parties are invited to submit information regarding the identification of acceptable contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
alternatives to this patented item to the Committee on Standards, ASTM Standards volume information, refer to the standard’s Document Summary page on
Headquarters, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Your the ASTM website.
4
comments will receive careful consideration at a
...